Applying epoxy into your garage floor is a good way to make it look great again while also remodeling your garage at the same time. Though when it comes to doing huge projects like this, you need to pay attention to the time it takes to finish it in order to save a lot of time and money.
In order to help you know how long it takes for a garage floor epoxy to dry and how it should be properly done, keep reading.
We’ve compiled to you a few tips on letting you know what you should do during the full process of this renovation such as from the preparation, application, and curing process.
- 1 The Exact Time that Floor Epoxy Starts to Dry
- 2 Tips for Preparation
- 3 Applying the Epoxy
- 4 Curing and Clean Up Stage
- 5 Conclusion
The Exact Time that Floor Epoxy Starts to Dry
Once the top coat of the floor epoxy has been applied, it will usually take around 12 hours to properly cure and at least a whole day for you to walk on it.
You will also need to wait for another day before you start putting things back into your garage. And you can finally place your car back into your garage after 72 hours of curing where the floor epoxy is fully cured.
Tips for Preparation
1. Plan Ahead
Ready all of the materials that you’re going to need such as your substrate and epoxy resin mix. Once you’re done preparing everything, make sure you’ve already gone through the process so you won’t end up skipping a step.
Make sure that you’re following the proper flow of the preparation, application, and cleanup. Jumbling the process may result in a huge mess that can slow you down and can even create mistakes.
2. Create a Sample Mix
If it’s still your first time in creating an epoxy resin mix then you should create a few sample mixes first to help you understand how it works. This lets you know the amount of time it takes to harden and help you see how the epoxy changes every hour.
You can also see how the pot will start to warm up and how much time you’re able to have before it gets hard on the container.
3. Clean Your Tools
Clean the brushes that you’re going to use for applying the floor epoxy into the garage floor. A good method of cleaning is to use sticky tape to remove any loose fibers that can mess up your workspace.
Make sure to use different brushes during each stage of the application process in order to get the best quality result. A chipping brush can be used if you’re planning on sanding the floor while when it comes to applying the finish coat, it’s best to use a quality brush for this.
Applying the Epoxy
1. Apply During the Right Time
Several epoxy mixes are highly affected by the temperature and humidity of the environment and it’s going to affect its curing process. Make sure to avoid applying the epoxy resin during times when it’s too hot or too cold.
This prevents the mixture to become easily brittle after the curing process and can also increase the time it would take to properly cure it.
2. Wait for a Moment
It’s also a good idea to let the epoxy resin mix to sit inside the container for a few minutes in order to let it properly mix itself. The more time you give the epoxy to mix then the curing process will start to accelerate.
If you want to let the epoxy slow down it’s time to mix then you could just add a wrapped ice pack to cool down the heating process.
3. Applying Another Layer
If the amount of epoxy that you’ve mixed and applied to your floor isn’t enough then wait for another 30 minutes before applying another layer. This is a good amount of time for the epoxy to harden a bit.
Once it’s time, apply the new batch of resin to layer the previous coat or just fill any low spots that you can see with the epoxy.
Curing and Clean Up Stage
1. Observe the Curing Process
Make sure that you’re watching the curing process from start to finish in order to get the best results and avoid you from applying more epoxy onto the floor.
The usual issues that may occur when left alone are surface contamination. This can cause problems during the process such as a fisheye or low spots which can create unevenness into your garage floor.
2. Using Different Products
There are different types of hardener and resin used for a garage floor epoxy and each of them has their own curing time. There are some hardeners that can slow the time it takes to cure the epoxy while other resins can also increase it.
3. Cure at Room Temperature
The best way of properly curing the floor epoxy is when you’re doing the process at room temperature. This allows you to have the best results in finishing the process and create a sturdier and long-lasting garage floor epoxy.
Make sure that you’re doing this process at the correct time and place as a sudden change of room temperature can highly affect the process.
4. Proper Cleaning Supplies
After the garage floor epoxy has finished curing, make sure to have the right cleaning materials with you in order to properly clean the garage.
The best way is to use denatured alcohol which is able to properly clean the place without affecting the cured epoxy floor. It’s also a good idea to use a fine brush for the touch-up stage.
Each state of applying epoxy to your garage floor is important as the whole process can start to tweak if some steps are forgotten. You need to think ahead of your plan, know the proper application process, and learn how to properly clean after the procedure is done.
Just make sure to get the right mix of resin and hardener in order to achieve the best results.